AKRS Equipment Solutions™

AKRS Equipment Solutions™

Search Used Inventory    Search Products & Site

Double tap to zoom

 

Features

Powered by 11.6-kw (15.5-hp)*, 675-cc (41.2-cu in.), V-twin, four-cycle gas engine

The Gator™ TX 4X2 is powered by an 11.6-kw (15.5-hp)*, 675-cc (41.2-cu in.), V-twin, four-cycle gas engine.

 

*The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. The actual operating horsepower will be less.

 

The model year 2015 TX (49 state) and beyond receives evaporative emissions components to meet Environmental Protection Agency (EPA) Clean Air Act requirements.

Engine features

This engine has several performance and reliability features:

  • Overhead valve design for greater efficiency and fuel economy
  • Full-pressure lubrication system
    • Oil filter is standard on the Gator TX 4X2 engine
  • Replaceable single-element air cleaner with remote intake
  • Large-capacity spark-arresting muffler
  • Low fuel consumption and large 18.9 L (5 U.S. gal.) fuel tank;
    fuel consumption at half load and average speed is as follows:
    • Gator TX 4X2: 1.3 L/h (0.35 U.S. gph)
  • EPA compliant

 

Precision-engineered drive system

Power is transmitted from the engine, through a continuously variable clutch system, to a transaxle. Power is transmitted from the transaxle directly to the rear axle.

 

Key elements of the drive system are as follows:

Variable-speed drive

 

The variable-speed drive consists of two clutches connected by a drive belt:

  • Drive clutch is attached to and rotated by the engine.
  • Driven clutch is attached to and drives the transaxle.

Features include:

  • Infinite selection of speeds (0 km/h to 32 km/h [0 mph to 20 mph])
  • No shifting necessary as operator increases speed
  • Adjusts speed to the load to avoid bogging down when going up a hill or through challenging conditions because the wrong gear was selected

How the variable-speed drive works:

  1. As the engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
  2. As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
  3. With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
  4. The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts the drive speed upward or downward, so the engine rpm remains constant at constant throttle position.

Transaxle

 

The transaxle is fully enclosed and runs in oil for reliability.

 

Helical gears are used for quiet operation.

 

Differential design reduces scuffing of the turf during turns because the inside wheels turn slower than the outside wheels (vehicles that have a solid axle shaft must skid the inside wheel when making a turn).

 

Traction assist (differential lock) is built into the transaxle:

  • Allows locking the rear drive wheels together
  • Provides increased traction in tough spots

A neutral start safety interlock is provided for the engine ignition system.

Heavy-duty rear axle housings

 

Gator TS 4X2

Bolt-on cast-aluminum rear-axle housings provide an extremely strong supporting structure.

  • Large, sealed bearings are located inside the housing for better protection
  • Forged-splined shaft for increased torsional strength

Gator TX 4X2

One-piece forged axles are splined for maximum strength.

  • Large, sealed bearings for better protection and load-carrying capabilities
  • Forged-splined shaft for increased torsional strength
  • Nodular cast-iron housing for increased durability

 

NOTE: The TS 4X2 is not sold in Australia/New Zealand.

All-wheel hydraulic disc braking with dual master cylinder

  • Four-wheel hydraulic disc brakes
  • Braided stainless-steel brake lines with banjo fittings for increased durability
  • Hand-lever-operated mechanical park brake system
  • Integral cast-iron rotors with wheel hubs for extended life
  • Automotive-style dual-circuit master cylinder with a see-through reservoir
  • Larger front and rear brake calipers with sintered metallic brake pads
  • Smooth-feeling engagement

 

Automotive-type rack and pinion steering with fully independent, single A-arm suspension

Automotive-type rack and pinion steering features include:

  • Smooth, responsive operation
  • Tight turning circle for excellent maneuverability
    • 2.74 m (9 ft) for Gator™ TX 4X2
  • Completely sealed for long life
Front suspension

Fully independent, single A-arm suspension features include:

  • 127 mm (5 in.) of total travel for better off-road control
  • Spring-over-shock dampening
  • Cast nodular iron 25-mm (1-in.) diameter spindles
  • Automotive-type maintenance-free rubber torsional pivots for long life and quiet operation
Rear suspension

The semi-independent coil over shock (COS) rear suspension system provides a softer ride.

Stable design

A low center of gravity gives excellent stability.

The cargo-box load is centered over the rear wheels for balanced weight distribution.

NOTE: Shown with the optional front bumper, brush guard, and floormat.

Tires

Four types of flotation tires are available for the Gator™ TX 4X2:

  • (A) AT (all terrain) tires
  • (B) Turf tires

Product attributes:

  • Both options, turf and AT, are 4-ply rated, and have an enhanced blend of material and more content that yields significantly more useful life
  • These tread patterns give a more aggressive showroom appeal
  • Each tire combines puncture resistance with a tread designed for maximum traction and performance

 

All tires offer a wide profile and are designed to be inflated at a low psi.

  • Provides good flotation and traction in mud, sand, and other wet or soft areas
  • Flexes over bumps and ruts for a smoother, more comfortable ride
  • Minimizes ground compaction to save turf and prevent ruts in soft ground
Wheels/tires

Code

TX 4X2

AT, front (two 22x9.5-10 4PR)
AT, rear (two 24x10.5-10 4PR)

1016

X

Turf, front (two 22x9.50-10 4PR)

Turf, rear (two 24x12.00-10 4PR)

1015

X

NOTE: John Deere recommends that all four or six (6x4 Gator™ models) tires be the same. Although the wheel and tire sizes remain the same, current tires should not be mixed with existing tires. The existing tires will remain available to service existing Gator utility vehicles.

Features operating conveniences such as high-back seats, cup holders, 12-V outlet, glove box, and fuel gauge

Numerous features offer the operator and passenger a comfortable ride and provide many operating conveniences.

  • Side-by-side bucket seating provides room for one operator and one passenger
  • Hip restraints serve as a handhold and help to keep the operator and passenger in their seats over rough terrain
  • Both seats tilt forward for dry storage and ease of service
  • Choice of adjustable or non-adjustable driver's seat
  • Hour-meter is standard to assist in maintaining regular service intervals
  • Integrated cupholders
  • 12-V outlet located on instrument panel

The control location and walk-through platform provide easy entry/exit for operator and passenger.


NOTE: Shown above with the optional front bumper, brush guard, front fender guard, and floor mat.

NOTE: The front bumper is standard on the Gator™ TH 6X4 Diesel.

  • All models feature a park brake indicator light, hour-meter, and tank-mounted fuel gauge as standard equipment
  • Traction assist (differential lock) is hand operated and conveniently located between the operator and passenger seats
  • Traction assist indicator light (Gator TH 6X4 only)
  • Glove box is located in the dash to provide a convenient storage area for small tools and the operator's manual
  • Grab bar is provided for the passenger
  • Center-mounted key switch
  • Additional storage is provided between the seats

Equipped with rear receiver hitch

The rear receiver hitch is standard equipment on the Gator™ TX 4X2 and TX Turf.

  • Versatile hitch accepts a 31.75-mm (1.25-in.) drawbar
  • No ball mount comes with the hitch

Durable deluxe cargo box

The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust, dents, and reduces noise.

Deluxe cargo box tailgate

The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.

 

The standard installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.

Deluxe cargo box tilt

The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist (A).

 

A prop rod (B) is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.

Integrated tie-down points

The deluxe cargo box offers integrated tie-down points for increased versatility. Tie-down points are located in the following areas:

  • Four corners inside the cargo box bed
  • Four points on the load guard directly behind the operator station (A)
  • Tie-down bars on either side of the cargo box (B)
  • Six points on the underside of the cargo box frame (circled)
Converting deluxe cargo box to a flat bed

The deluxe cargo box easily converts to a flat bed. The flatbed configuration allows loading larger cargo.

Optional accessories

Optional accessories for the deluxe cargo box include:

  • Factory-installed brake and taillight
  • Factory-installed spray-in liner (not shown)
    • Improves skid resistance and surface abrasion protection
  • Cargo box bed mat
  • Cargo box power lift (not shown)
Specifications
 

Box capacity

Volume 465 cu L (16.4 cu ft)
Weight 272 kg (600 lb)

 

 

Box dump angles (degrees)

Manual dump 43 degrees +/-1
Power dump 43 degrees +/-1


CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

Specifications

Key Specs

Engine power 11.6* kW
15.5 hp
Maximum traveling speed 0-32 forward km/h
0-20 forward mph
0-31.2 reverse km/h
0-19.4 reverse mph
Cargo box dimensions 1143 x 304.8 x 1320 mm
Cargo box capacity 272 kg
600 lb
Towing capacity 454 kg
1000 lb
Front suspension Independent spring over shock, single A-arm
Rear suspension Semi-independent coil over shock (COS) system
Final drive Fully enclosed; oil bath
Four wheel drive No
Fuel capacity 5 g

Engine

Type 4-cycle gas
Displacement 675 cc cc
41.2 cu in.
Power 11.6* kW
15.5 hp
Cooling system Air

Drivetrain

Transmission Continuously variable transmission (CVT)
Final drive Fully enclosed; oil bath
Four wheel drive No
Traction assist Mechanically Activated Differential Lock
Descent control No
Maximum traveling speed 0-32 forward km/h
0-20 forward mph
0-31.2 reverse km/h
0-19.4 reverse mph

Suspension

Front Independent spring over shock, single A-arm
Rear Semi-independent coil over shock (COS) system

Brakes

Type All-wheel hydraulic disc
Park brake Rear mechanical disc, hand operated

Tires

Front Two 22x9.50-10, 4 PR,
Rear  
Dry weight 1120 lb

Dimensions / Capacities

Wheelbase 1955.8 mm
77 in.
Front tread centers 1270 mm
50 in.
Rear tread centers 1219.3 mm
48 in.
Height 1108 mm
43.6 in.
Width 1525 mm
60 in.
Length 2.75 mm
108.1 in.
Ground clearance 14.4 cm
5.7 in.
Fuel capacity 5 g
Cargo box dimensions 1143 x 304.8 x 1320 mm
45 x 12 x 52 in.
Cargo box capacity 272 kg
600 lb
Payload capacity 454 kg
1000 lb
Towing capacity 454 kg
1000 lb
Hitch Standard 2-in. receiver

Features

Color Green/Yellow
Power steering No
Battery 340 Cold Cranking Amps @ -18C (0F)
Alternator 16.6 @ 3700 rpm (regulated) amp
Instrumentation Fuel Gauge, Hour Meter listed in the Sales Manual
Storage Cup Holders, Glove Box
Seating Bucket Seats

Accessories and Attachments

Alternator

+ High-Capacity Alternator Kit (TX) - BM22770

 

Backup Alarm

+ Backup Alarm Kit (S/N 90.001-...) - BM26351

 

Bumper

+ Front Bumper - BM23458

+ Front Bumper and Brush Guard - BM23459

+ Front Fender Guard - BM23457

+ Rear Bumper - BM22767

 

Cargo Box

+ 19 L (5 gal) Pail Holder - BM23849

+ Cargo Bed Extender - BM25700

+ Cargo Box Bed Mat - BM22772

+ Cargo Box Divider - BM22769

+ Cargo Box Power Lift - BM23734

+ Cargo Box Side Extension Kit - BM24901

+ Label kit for toolboxes (Green & Yellow) - BM26220

+ Remote Cargo Box Release Kit - BM24804

+ Side Storage Box - BM22776

+ Side Tool Rack - BM22775

+ Tailgate w/ brake and tail lights for toolboxes - BM26161

 

Carts

+ Utility Cart, 21 Steel - LPUT21JD

 

Cover

+ Gator Cover - LP93547

+ Large Deluxe Seat Cover - Yellow - LP92634

+ Large Seat Cover - Yellow - LP92334

+ Seat Cover - Camo - LP92333

+ Vehicle Cover, Cab or ROPS - Black - LP93107

+ Vehicle Cover, Cab or ROPS - Camo - LP93103

 

Drawbar

+ 48mm (1 7/8-in.) hitch ball for ball-type hitch. Ball Mount sold separately. - PM05101

+ 51mm (2-in.) hitch ball for ball-type hitch. Order ball mount separately. - PM05201

+ Drawbar/ ball mount for 1.25 in. receiver hitch - BM23989

 

Front Rack

+ Front Hood Rack - BM23456

 

Guards

+ Cargo Box FenderGuard - BM22811

 

Horn

+ Horn kit - BM23193

 

Lighting

+ Beacon Light - BM22405

+ Beacon Light Kit - Deluxe Cab - BM21649

+ Brake and Taillight Kit - BUC10172

+ Deluxe Light Kit - BUC10173

+ Front Work Light Kit - Deluxe Cab - BM21651

+ Interior Light Kit - Deluxe Cab - BM21656

+ Rear Work Light Kit - Deluxe Cab - BM21652

+Tail Light Protectors - BM22773

 

Mirrors

+ Exterior Mirrors (2) Kit - BM21645

 

Operator''s Station

+ Deluxe Glass Cab - BM22600

+ Electrical Kit - Deluxe Glass Cab - BM22138

+ Floor Mat - BM25000

+ Forced-Air Heater Kit - BM23578

+ Sunshade - LP45544

+ Visor (1) Kit - Deluxe Cab - BM21646

+ Windscreen - BM21466

 

Operator's Manual And Decal Kit

+ Spanish OM/Label Kit TS, TX, TX Turf, TH Gas, TH-Diesel MY18 - BUC10442

 

Rear Receiver Hitch

+ Rear Mount Cable Assembly - AM137110

 

Seat

+ Parts for Adjustable Driver's Seat - BM23799

 

Spark Arrester

+ Spark Arrester Screen for Muffler - AM108146

 

Speed Control

+ Rough Terrain Kit - BM22543

 

Sprayers

+ Tow-Behind High Performance Sprayer, 45 gal. (170 L), requires LP22884 or LP22885 boom - LP39963

+ Tow-Behind Sprayer, 45 gal. (170 L) - LP20485

 

Sprayers

+ 170.344 L (45 gal) Bed Sprayer - LP20852

+ 170.344 L (45 gal) High Performance Sprayer - LP22908

+ 25 Gallon Bed Sprayer - LP33597

+ GatorPal High Pressure Washer (2700 psi, Honda engine) - LPGP2700GH

+ GatorPal High Pressure Washer (2700 psi, Subaru engine) - LPGP2700GS

+ HP Standard Gator Boom - LP22911

+ High Performance Sprayer Precision Boom (12.5 ft) - LP22885

+ High performance boomless nozzles - LP22884

 

Spreaders

+ 17AT Cart - LPPCT17ATJD

+ 3 cu. ft. Fertilizer Spreader - LP49056

+ 3 cu. ft. Salt Spreader - LP49055

+ Spreader Hitch and Controls - LP53808

 

Storage

+ Gator Gear Organizer (Camo) - LP19877

+ Gator Toolbox - LP19886

+ Side Opening Toolbox - BM26160

+ Top Opening Toolbox - BM26162

 

Suspension

+ Heavy-Duty Suspension Kit - BM20414

+ Tire Chains

+ Tire Chains (for HPAP 24x10.5-10 or HPAT 24x12-10) - TY25800

 

Winch

+ Warn Winch 1360.78 kg (3000 lb) - BM24442

+ Winch Accessories Kit - BM21392

 

Windshield

+ Windshield Washer Kit - BM21648

+ Windshield Wiper Kit - BM21462

AKRS Equipment Solutions