AKRS Equipment Solutions™

Features
High clearance handles heavy residue levels
Excellent fore-aft and vertical clearance between standards (arrows above) allows the soil and residue to freely flow through the plow:
- Both rigid and flex plows are designed to handle tall and heavy residue levels.
Clearance
Fore and aft | Vertical |
864 mm (34 in.) | 851 mm (33.5 in.) |
Adjustable width of cut
The operator can change the plow's width of cut to match the tractor horsepower and soil conditions.
-
Narrow in tough soil
-
Wider in lighter soil
3710 Rigid Plow
The rigid plow has a width-of-cut range of 356 mm to 559 mm (14 in. to 22 in.) on land and 508 mm to 559 mm (20 in. to 22 in.) in furrow.
- Economical manual adjustment (turnbuckle is standard equipment)
- Convenient hydraulic cylinder adjustment is optional
- Pointer and decal allow returning to a predetermined width of cut
3710 Flex Plow
The flex plow has 356 mm to 559 mm (14 in. to 22 in.) of cut.
Adjustments are made by adjusting two turnbuckles (arrows) to a predetermined length specified in the operator's manual.
Scissor-type landing helps with tight turns on rigid models
The rigid model uses a scissor-type landing adjustment to set the first bottom in relationship to the rear tractor tire for the different widths of cut:
- Design uses minimum space, gives a clean-style appearance, and has a full range of adjustment.
- Economical turnbuckle is used to make the adjustment.
- Operator-supplied 76-mm x 203-mm (3-in. x 8-in.) American Society of Agricultural Engineers (ASAE) tie-bolt hydraulic cylinder may be used in place of a turnbuckle for in-furrow applications.
Land wheels on rigid models are tied to the Adjust-O-Cut bar for automatic setting for each width of cut
Land wheels help to stabilize the plow in both the working and transport positions. They also control the depth of plowing and work in conjunction with raising and lowering the plow.
Land wheels on rigid plows are tied to the Adjust-O-Cut bar for automatic setting for each width of cut.
A single wheel is standard on the six-bottom model; dual wheels are standard on the seven- and eight-bottom models and optional on the six-bottom model (recommended in softer soils).
-
Provides good trailing characteristics in transport.
Flex models are equipped with dual, staggered Walk-Over™ land wheels
Land wheels on flex plows have four adjustment positions (arrow) to allow setting the assembly for 406-mm, 457-mm, or 508-mm (16-in., 18-in., or 20-in.) widths of cut or transport:
- Depth stops are used for easy adjustment of the depth.
Dual, staggered Walk-Over wheels are standard on flex plows:
- Allow the plow to trail like a cart
- Distribute weight evenly between both wheels
- Minimize bulldozing in soft soil
- Allow better residue flow
- Walk over obstacles and across dead furrows
Spring-reset standards available to work non-stop in rocks
The double-pivot design of the spring-reset standard uses tension spring force to return the standard to the working position.
- For heavier-duty applications
- Positive reset
- Non-adjustable trip force; factory set at 2727-kg (6000-lb) nominal
- Floats over buried rock
- Unhooks from ledge rock
Safety-trip standards for normal plowing conditions
Safety-trip standards provide an economical means for protection—suited for areas without rocks:
- No backing to reset, just raise
- Shim-adjustable trip force
- 2727-kg (6000-lb) nominal trip force (set at the factory)
- Smooth surfaces for good residue flow
- Few moving parts equals high reliability
Light-draft NU bottoms permit high-speed plowing
The NU bottoms are set behind the mainframe to prevent the mainframe from becoming a pinch-point for residue. They are designed for light draft and high-speed plowing.
- Operators often find they can plow a gear higher than with competitive plows
- Greater productivity and fuel economy
- Speeds up to 10 km/h (6 mph)
Available in 400-mm (16-in.) and 450-mm (18-in.) sizes with an unpolished finish.
The maximum plowing depth are as follows:
BOTTOM MAXIMUM | PLOWING DEPTH* |
400 mm (16 in.) | 305 mm (12 in.) |
450 mm (18 in.) | 356 mm (14 in.) |
* In some soil conditions at plowing depths in the 254-mm to 356-mm (10-in. to 14-in.) range, soil may boil over the moldboard, resulting in poorly defined furrows.
Shares for NU bottoms
Both the NU 400 and the NU 450 come standard with heavy-duty, full-cut shares.
A variety of shares are available through Parts to match the plowing conditions:
Image | Part | Description |
1 | NU400 | Regular, narrow cut |
2 | NU400 | Heavy duty, narrow cut |
3 | NU400 | Heavy duty, full cut |
4 | NU450 | Heavy duty, narrow cut |
5 | NU450 | Heavy duty, full cut (standard equipment) |
6 | NU450 | 500-mm over-cut (for use when wide widths of cut or complete slicing is required) |
7 | NU450 | Hard-faced gumbo (for heavy soil conditions when penetration is a problem |
8 | NU400 | Hard-faced (for areas where abrasive soil causes rapid wear of heavy-duty shares—not for use in rocks) |
9 | NU450 | Hard-faced (for areas where abrasive soil causes rapid wear of heavy-duty shares—not for use in rocksfor) |
The gumbo moldboard (A32211) is available for NU 400 bottom and is recommended for use in heavy soil (gumbo) conditions. It is similar to the NU 400 bottom except that it has less area at the wing tip.
- Moldboard will not be forced upward by soil movement as much as NU 400.
- Permits soil to push off easier for better scouring and lighter draft.
John Deere furnishes a replacement share for any John Deere plow share that breaks before the share reaches the following wear limits (labor not included; wear to be measured perpendicularly across the middle of the front bolt hole):
- 13-mm (1/2-in.) wear, 89 mm (3.5 in.) remaining.
Trashboards for NU bottoms
Plastic or steel trashboards can be added to NU bottoms to improve coverage in tall, heavy residue. Plastic trashboards are only recommended for non-abrasive soils where scouring is a problem with steel trashboards.
Shear-bolt coulters suited for areas without rocks
Economical design of the shear-bolt coulters is suited for areas without rocks:
- Few moving parts
- Good depth adjustment range
- Good lateral adjustment range
Adjustable-force cushion coulters available for rocky or normal field conditions
Specifications
Key Specs
Option 1 | Rigid plow On land: 356 to 559 mm 14 to 22 in. In furrow: 508 to 559 mm 20 to 22 in. |
Option 2 | Flex plow: 356 to 559 mm 14 to 22 in. |
Plowing depth | 305 mm 12 in. 356 mm 14 in. |
Hitch
Steering | Integral, in-furrow No Integral, on-land No Semi-integral, on-land No Drawn, in-furrow Yes: 6, 7 Drawn, on-land Yes: 6, 7, 8, 9, 10 |
Reversible | No |
No. of bottoms
Option 1 | 6 |
Option 2 | 7 |
Option 3 | 8 |
Option 4 | 9 |
Option 5 | 10 |
Total width of cut
Adjustment | Standard: Manual Optional: Hydraulic |
Option 1 | Rigid plow On land: 356 to 559 mm 14 to 22 in. In furrow: 508 to 559 mm 20 to 22 in. |
Option 2 | Flex plow: 356 to 559 mm 14 to 22 in. |
Clearances
Vertical | 851 mm 33.5 in. |
Fore-aft | 864 mm 34 in. |
Standards
Shearbolt | No |
Safety trip | Yes |
Spring reset | Yes |
Hydraulic | No |
Coulters
Option 1 | Yes |
Option 2 | Yes |
Bottoms
Option 1 | Plowing depth 305 mm 12 in. 356 mm 14 in. Reversible bottom - steel: 406 mm 16 in. |
Option 2 | Reversible bottom - steel: 450 mm 18 in. |
Frame
Option 1 | 203x203 mm 8x8 in. |
Expandable | No |
AKRS Equipment Solutions
-
Ainsworth, NE
87797 432nd Avenue
Ainsworth, NE 69210
402-387-1800
Get Directions -
Albion, NE
2361 State Highway 91
Albion, NE 68620
402-395-2173
Get Directions -
Auburn, NE
73136 Hwy 75
Auburn, NE 68305
402-274-4941
Get Directions -
Aurora, NE
609 Q St / W Hwy 34
Aurora, NE 68818
402-694-2191
Get Directions -
Broken Bow, NE
44098 Hwy 2
Broken Bow, NE 68822
308-872-2497
Get Directions -
Central City, NE
1026 G St / W Hwy 30
Central City, NE 68826
308-946-3041
Get Directions -
Crete, NE
2185 County Road H
Crete, NE 68333
402-826-4347
Get Directions -
David City, NE
1707 N 4th Street
David City, NE 68632
402-367-3636
Get Directions -
Elkhorn, NE
11550 N. 204TH ST.
Elkhorn, NE 68022
402-238-2211
Get Directions -
Geneva, NE
736 South 13th Street
Geneva, NE 68361
402-759-3139
Get Directions -
Grand Island, NE
4050 W Stolley Park Road
Grand Island, NE 68803
308-384-8777
Get Directions -
Gretna, NE
15151 South Hwy 31
Gretna, NE 68028
402-332-4967
Get Directions -
McCook, NE
1207 West B Street
McCook, NE 69001
308-345-2730
Get Directions -
Neligh, NE
1110 E Hwy 275
Neligh, NE 68756
402-887-4158
Get Directions -
Norfolk, NE
3303 W Norfolk Ave
Norfolk, NE 68701
402-371-7333
Get Directions -
North Platte, NE
2700 East Walker Road
North Platte, NE 69101
308-532-5080
Get Directions -
Oberlin, KS
126 N. Penn
Oberlin, KS 67749
785-475-3833
Get Directions -
O'Neill, NE
49110 Hwy 20
O'Neill, NE 68763
402-336-1800
Get Directions -
Ord, NE
711 U Street
Ord, NE 68862
308-728-7770
Get Directions -
Osceola, NE
13006 N Road
Osceola, NE 68651
402-747-2051
Get Directions -
Plainview, NE
53471 W Hwy 20
Plainview, NE 68769
402-582-4840
Get Directions -
Ravenna, NE
42185 Hwy 2
Ravenna, NE 68869
308-452-3254
Get Directions -
Seward, NE
977 280th Road
Seward, NE 68434
402-643-3616
Get Directions -
Spalding, NE
81863 N Mill St
Spalding, NE 68665
308-497-2511
Get Directions -
St. Paul, NE
1339 Hwy 281
St. Paul, NE 68873
308-754-4419
Get Directions -
Syracuse, NE
257 N. 30th Road
Syracuse, NE 68446
402-269-2241
Get Directions -
York, NE
3221 N Lincoln, PO Box 129
York, NE 68467
402-362-6607
Get Directions -
Lincoln, NE
150 NW 40th Street
Lincoln, NE 68528
402-438-6189
Get Directions